Crystal Tester 1Hz-50MHz DIY Kit manual | Hertz

Please download to get full document.

View again

of 4
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information Report



Views: 50 | Pages: 4

Extension: PDF | Download: 0

Related documents
Manual For The SainSmart & Other Brands DIY Crystal Tester & 50Mhz Counter
  1-50Mhz Frequency counter This document describes the construction of small frequency counter with a cheap PIC microcontroller and a few seven-segment LED digits. The main features of the frequency counter are: ã   frequency range 1 Hz ... 50 MHz ã   five digits resolution (display for example x.xxxx kHz, x.xxxx MHz, or MHz) ã   automatic range switching with different gate times ã   optional addition or subtraction of a frequency offset (programmable) ã   optional preamplifier for the input signal ã   very low component count: a PIC 16F628, 5 7-segment LED displays, a 20-MHz crystal and a few resistors ã   optional (configurable) power-saving mode which automatically turns the display off if the frequency didn't change significantly within 15 seconds main schematic:    Power on,no signal Crystal test(8M)  The display range is automatically switched to give the maximum readout accuracy (with 5 digits). The gate time is also selected automatically as listed in the following table: Frequency range Display Gate time Decimal point 0 ... 9.999 kHz X . XXXX 1 second flashing (which means kHz ) 10 ... 99.99 kHz XX . XXX 1/2 second flashing 100 ... 999.9 kHz XXX . XX 1/4 second flashing 1 ... 9.999 MHz X . XXXX 1/4 second steady (which means MHz ) 10 ... 50.00 MHz XX . XXX 1/4 second steady Adding or subtracting an offset frequency If the counter is used in a shortwave receiver or transceiver, you may want to add or subtract an offset value from the measured frequeny. The offset frequency is the same as the intermediate frequency in many cases, because the counter is usually connected to the receivers VFO (variable frequency oscillator). For this purpose, a programming mode (aka setup mode ) has  been implemented in the firmware so you can enter an offset frequency without reprogramming (or even reassembling) the PIC firmware.   The program flow chart on the left shows how to enter programming mode, how to select a menu, and how to execute the associated function. To enter programming mode, press and hold the  programming key until the PIC shows ProG on the LED display. Then release the key. You are now in the first menu of the programming mode. To select the next menu, press the key for a  short   time (less than a second). To execute the selected function, press the key for a longer time (more than a second). The menu functions are :  ã   Quit : Aborts programming mode without changing anything. ã   Add : Saves the previously measured frequency permanently, so it will be added in future. ã   Sub : Saves the previously measured frequency permanently, so it will be subtracted in future. ã   Zero : Sets the frequency offset to zero, so the display will show the measured frequency without offset. The previously programmed offset will be lost. ã   Table : Allows you to select a predefined offset value from a table. The table itself is also located in the PIC's data EEPROM, so you may find different values in it. When skipping through the table, the frequencies are shown in numeric form, like 455.0 (kHz), 4.1943 (MHz), 4.4336 (MHz), 10.700 (MHz). After selecting an entry (long keypress), you will be taken back to the main menu to select Add or Subtract . ã   PSave / NoPSV : turns the power-saving on/off. In power-saving mode, the display is turned off after 15 seconds of no significant change in frequency, and on again as soon as the frequency changes  by more than a few dozen Hertz (in the 3..4 MHz measuring range). Added in May 2006 for battery-powered equipment like QRP transceivers. Attention: Max input signal voltage <=5V! Crystal test range about 1M-45M When you input singal at  in !  and  - ! ,don # t use the ext  power plug.
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!