ASL Intercom PS29M

Please download to get full document.

View again

of 11
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Information Report
Category:

Business

Published:

Views: 0 | Pages: 11

Extension: PDF | Download: 0

Share
Related documents
Description
Download ASL Intercom PS29M
Transcript
  • 1. PRO SERIES USER MANUAL FOR THE PS 29 MCONTENTS GENERAL DESCRIPTION 3 UNPACKING 3 INSTALLATION 3 FRONT PANEL CONTROLS 4 REAR PANEL CONNECTORS 4 SIDE PANEL CONTROLS 5 CABLING 6 PARTY LINE, TECHNICAL CONCEPT 7 GUARANTEE 7 TECHNICAL SPECIFICATIONS 7 User Manual PS 29 M / Issue 1 © 2000 ASL Intercom, Utrecht, Holland.
  • 2. 2 User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland.
  • 3. 1.0 GENERAL DESCRIPTION The PS 29 M is a portable dual channel user station. The unique ASL Call system provides both a flashing red It is housed in a strong ABS case and it is provided with a LED and a very distinctive and characteristic sound steel beltclip. signal. Smooth operation is guaranteed with the CALL button. A momentary push makes the red LED flash, Both channels have independant Volume (listen level) whilst holding the button for two seconds will activate the controls, Talk and Call switches, Talk and Call LED CALL sound signal. The volume of the sound signal indicators and Sidetone trimmers. (buzzer) can be adjusted at the side panel. Special attention has been paid to the intelligibility of Fully electronic switching increases reliability and allows speech. By applying low noise/high speed opamps, a for : speech presence filter and a specially developed high - soft microphone ON switching, latched or momentary power bridged headphone amplifier, communication is - remote Mic Mute facility. very comfortable even in environments with high background noise level. As an option, a XLR-6 headset connector can be fitted allowing the user to hear channel A at the left headset can and channel B at the right headset can. 2.0 UNPACKING The shipping carton contains the parts below: After unpacking the unit please inspect for any physical damage to the unit, and retain the shipping carton and * The PS 29 M relevant packing materials for use should the unit need * User manual returning. If any are missing, contact your dealer. If any damage has occured, please notify your dealer imediately so that a written claim can be initiated. Please ASL has taken great care to ensure this product reaches also refer to the guarantee section of this manual. you in flawless condition. 3.0 INSTALLATION This PS 29 M will form part of an existing or new intercom To connect the PS 29 M onto the intercom system, use system, and connections to it is straightforward. There are professional flexible microphone cable with 2 wires and 1 no separate power connections, or batteries to install, as shield only. Connect the system intercom cables into the the necessary DC voltage are derived from the intercom LINE connector sockets on the rear panel. Finally connect master station or power supplies, via the intercom the listening headset plug into the HEADSET connector, connections cable. also on the rear panel. The PS 29 M is fully protected against mis-wiring (reverse power) or short-circuit in the interconnecting cables.User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland. 3
  • 4. 4.0 FRONT PANEL CONTROLS 1 VOLUME control knobs These knobs adjust the listen levels for each channel separately. You can listen to one channel or to both channels at Volume Volume the same time. 2 TALK buttons These buttons allow you to talk to each channel separately or simultaneously. The large green led indicates if the talk function is activated. Latched switching: 3 2 1 When a TALK button is pressed quickly, the 3 microphone will be switched on, and is electronically CALL buttons latched. When pressed again, the microphone will be These buttons activate the call system. switched off. The Call functions of both channels are independant which means that simultaneous operation is possible. Momentary switching: A momentary push will send a call signal to all stations When a TALK button is pressed and held, the connected to the intercom channel and the call LEDS microphone will be active, until the button is released. will start flashing. Press and hold the button for 2 seconds will activate When the microphone is latched on, it can be muted the call buzzer,if not muted. by a Mic Mute from a PRO Series master station or After the CALL button is released the LEDS will power supply. continue to flash for further 2 seconds. 5.0 REAR PANEL CONNECTORS 4 LINE connector channel B 5 LINE connector channel A These connectors are for connecting the PS 29 M to the intercom system (two separate intercom channels A and B). Pin assignments : 1. 0V / ground shield 2. +30V power wire 3. audio wire Both connectors are for input. 6 HEADSET connector An XLR-4 type connector for the connection of the local headset. This must have a can impedance of 200 ohms (or greater). The mic may be of the dynamic or electret type. Pin assignments : 1. Shield mic. (GND) 2. mic. + 3. phones + 4. phones - Optional : Binaural XLR-6 headset connector4 User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland.
  • 5. 6.0 SIDE PANEL CONTROLS 7 SIDETONE trimmer channel A 8 SIDETONE trimmer channel B These trimmers adjust the level of your own voice as you hear it in your headset. There is a trimmer for each channel. Adjustment procedure : - set trimmer in start position : fully clockwise. - switch off the microphone of all connected stations. - switch on the TALK of the channel you want to adjust. - turn up volume. - speak into the headset microphone. - adjust the listen level by turning the sidetone trimmer. The operating area is between fully clockwise and minimum level. Follow this procedure for both channels. Adjusting the sidetone does not affect the level of your voice as it is heard by other stations. 9 9 BUZZER VOLUME trimmer 7 This trimmer adjusts the volume of the internal buzzer. buzzer The buzzer will be activated if a CALL-button is volume side pressed for longer than 2 seconds and the buzzers are A tone serial number 10 not muted on the power supply. 8 side mic. 10 MIC GAIN B tone gain The mic gain can be adjusted by a trimmer. To increase mic gain turn clockwise. To decrease mic gain turn counterclockwise. intercom intercom headset line A line BUser Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland. 5
  • 6. 7.0 CABLING For the PRO Series Intercom system the interconnecting cables are of the shielded two-conductor microphone cable type and the intercom line connectors are of the XLR-3 type. Audio and Call signals are on XLR pin 3, DC power is on XLR pin 2. XLR pin 1 is connected to the shield of the cable which functions as the common return for audio and power. Since the audio signal is transferred in an unbalanced Ú way, certain rules have to be obeyed when installing the cables of an intercom network. This is to avoid earth loops and to minimize power loss and the possible effect of electromagnetic fields. These rules are: ! Use high quality (multipair) cable. ! Keep cables parallel as much as possible. For interconnecting user stations, power supplies and When two (multi channel) units in a network are accessories in an ASL Intercom network, use high connected by more than one cable, make sure that quality shielded two-conductor (minimum 2x 0.30 these cables are parallel to each other over the whole mm2) microphone cable only. distance between those units. When using multipair In case of a multi channel intercom network, use high cable, parallelism is ensured in the best possible way. quality microphone multipair cable only, each pair consisting of two conductors (minimum 2x 0.15 mm2) ! Avoid closed loops. with separate shield. Multipair cable should also have Always avoid that cables are making a loop. So-called an overall shield. ring intercom should not physically be cabled as a ring. All cable routes should have a star configuration, ! Use flexible cables. with the central earthing point (usually close to the Use flexible single and multipair microphone cable power supply position) as the center of the star. instead of cable with solid cores, especially when the cable is subjected to bending during operation or ! Keep cables away from electromagnetic sources. installation. Keep intercom cables away from high energy cables, e.g. 110/220/380V mains power or dimmer controlled ! Separate cable screen to XLR pin 1. feeds for spotlights. The screen of each separate microphone cable and/or Intercom cables should cross high energy cables at an the screen of each single pair in a multipair cable, angle of 90E only. should be connected to pin 1 of each XLR-3 Intercom cables should never be in the same trunking connector. Do not connect this cable screen to the as energy cables. metal housing of the connector or to metal wall boxes (outlets). ! Place power supply in a central position. See page 10: Earthing Concept. In order to avoid unacceptable power losses, place the power supply as close as possible to where most ! Cable trunks, connection boxes and overall power consumption occurs or, in other words, most multipair cable screen to clean earth. user stations are placed. Metal cable trunks, metal connection boxes and overall multipair cable screen should be inter- ! Connect ASL power supply to a clean mains connected and, at one point (the central earthing outlet. point) in the intercom network only, be connected to a The ASL power supply may be connected to the mains clean earth or a safety earth. power outlet to which other audio equipment is See page 10: Earthing Concept. connected. Avoid using mains outlets which also power dimmer controlled lighting systems. ! Keep metal connection boxes and cable trunks isolated from other metal parts. In case of more complex installations, dont hesitate to Metal housings for intercom cables and connectors contact us. Please send us a block diagram of the should be mounted in such a way that they are planned network with a list of all user stations and their isolated from other metal cable and connector positions, and we are happy to advise you on cabling lay housings and from any other metal construction parts. out. Ú See Party Line, Technical Concept 6 User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland.
  • 7. 8.0 PARTY LINE, TECHNICAL CONCEPT 9.0 TECHNICAL SPECIFICATIONS PS 29 M ASLs PRO Series offers a complete two way (full duplex) POWER CONSUMPTION communications system. current (at 30 V DC) 30 mA quiescent Users of the system are connected via a party line. 45 mA signalling Master stations (with built-in power supply), beltpacks, 170 mA at max. output + signalling speaker stations and power supplies are interconnected via standard microphone cable. One wire is used as an MIC. PREAMP audio line, one as a power line and the screen of the mic. impedance 200 ohms cable functions as earth/return. gain 40 dB - 70 dB (adjustable internally) presence filter +6 dB at 5 kHz Current drive is used for signal transfer. Each station frequency response 200 Hz - 13 kHz (-3 dB) utilises a current amplifier to amplify the microphone V electret mic +9 V DC signal and place it on the common audio line where, due to the constant line impedance (situated in the power HEADPHONES DRIVER AMP supply between XLR pin 3 and 1), a signal voltage is max. load 200 ohms developed which can be further amplified and sent to max. output level normal 14 V rms (200 ohms) headphones or loudspeakers. binaural 8 V rms (400 ohms) max. output power normal 0.5 W rms (each can) This principle has three advantages: binaural 0.16 W rms (each can) - the use of a single audio line allows several stations to talk and listen simultaneously. INTERCOM LINE DRIVER - due to the high bridging impedance offered by each max. output current 3 mA rms station, the number of stations on line has no output impedance > 150 Kohms influence on the level of the communications signal. - power and audio to the intercom stations use the SIDETONE same cable. rejection 0 - 30dB adjustable The Call signal is also sent as a current on the audio line. BUZZER It develops a DC potential over the line impedance which max. SPL 101 dBA will be sensed by each station and interpreted as a Call signal. DIMENSIONS AND WEIGHT width 90 mm height 38 mm depth 124 mm weight 325 g GENERAL SYSTEM SPECIFICATIONS 10.0 GUARANTEE intercom line impedance 350 ohms (1kHz) 2.2 Kohms (DC) intercom line audio level nom. -18 dBu This unit is warranted by ASL Intercom to the original end- max. +4 dBu user purchaser against defects in workmanship and dynamic range 80 dB materials in its manufacture for a period of one year from call send signal +2.8 mA date of shipment to the end-user. call receive signal threshold +2.4 V DC supply voltage +30 V DC (12 V to 32 V) Faults arising from misuse, unauthorised modifications or mic mute power interrupt time 0.1 sec accidents are not covered by this warranty. If the unit is faulty it should be sent in its original packing, to the supplier or your local ASL dealer, with shipping prepaid. A Note: 0 dBu = 775 mV into open circuit note must be included stating the faults found and a copy of the original suppliers invoice. ASL reserves the right to alter specifications without further notice. THIS PRODUCT WAS DESIGNED, DEVELOPED AND MANUFACTURED BY : AMPCO SOUND LAB BV MAARSSEN (UTRECHT) HOLLAND.User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland. 7
  • 8. 8 User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland.
  • 9. User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland. 9
  • 10. 10 User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland.
  • 11. User Manual PS 29 / Issue 1 © 2000 ASL Intercom, Utrecht, Holland. 11
  • Recommended
    View more...
    We Need Your Support
    Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

    Thanks to everyone for your continued support.

    No, Thanks
    SAVE OUR EARTH

    We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

    More details...

    Sign Now!

    We are very appreciated for your Prompt Action!

    x